Skip to content

Water Hardness in White Plains, New York

Does White Plains have hard water?

No. The water is soft.

White Plains Water Department delivers water at 30 ppm (1.8 grains per gallon), which this site rates Soft and the USGS classifies as soft (0–60 mg/L as calcium carbonate). That is 35 ppm softer than the New York average of 65 ppm, and softer than 85% of the 428 cities listed on this site.

Hardness 30 ppm 1.8 grains per gallon
USGS Class Soft No softener needed
Rank in NY 8 of 10 hardest first
Water Source Surface White Plains Water Department

30 PPM in Every Unit

Appliance manuals, test strips and utility reports each use a different hardness unit. These are the same White Plains reading expressed in each one.

UnitWhite PlainsUsed by
mg/L as CaCO₃ (ppm)30Utility water-quality reports, USGS
Grains per gallon (gpg)1.8Softener sizing, most US dishwasher manuals, test strips
German degrees (°dH)1.7European-made dishwashers and coffee machines
French degrees (°fH)3Some filter and descaler instructions
mmol/L0.3Laboratory reports

Dishwasher setting for White Plains: 1.8 gpg or 1.7 °dH, rounded up to the machine's nearest step. The USGS bands are soft 0–60, moderately hard 61–120, hard 121–180 and very hard above 180 mg/L; this site splits the top band at 250 to separate hard from very hard.

What 30 PPM Does in a White Plains Home

At 30 ppm there is no scale to speak of. Soap lathers freely, glassware dries clear and a water heater on this supply holds its rated efficiency. A softener would have nothing to remove.

Water heaters

The clearest measured effects of hardness come from a 2009 study the Water Quality Research Foundation commissioned from the Battelle Institute. Scaled to White Plains's 1.8 gpg, its gas storage-heater results work out as follows; softened water held full efficiency in the same tests.

ApplianceBattelle findingAt 1.8 gpg
Gas storage heater, 50 gal hot water/day4% efficiency loss per 5 gpg over 15 years1% loss
Gas storage heater, 100 gal/day8% per 5 gpg, capped at the 48% measured at 30 gpg3% loss
Electric storage heater0.4 lb of scale per year per 5 gpg0.1 lb/year
Tankless gas heaterPlugged with scale after 1.6 years on 26 gpg waterLow risk
ShowerheadsLost 75% of flow in under 18 months on hard waterOccasional vinegar soak

Laundry and dishes

Hardness minerals bind with detergent before it can clean, which is why dose charts step up for hard water. For White Plains: Use the label's minimum dose; soft water needs no extra detergent.

Where White Plains's Water Comes From

White Plains Water Department supplies White Plains from surface water (rivers, lakes and reservoirs). Surface water has little contact with mineral-bearing rock, so its hardness mostly reflects the watershed's geology and tends to run lower and steadier than well water.

The supply has a pH of 7.1, inside the EPA secondary range of 6.5–8.5, and total dissolved solids of 48 mg/L, well under the EPA secondary standard of 500 mg/L. Hardness is the largest part of dissolved solids in most municipal water, which is why the two tend to rise together.

The figure on this page is the utility's reported average. Blended systems vary by season and neighborhood, so for the current number check the utility's Consumer Confidence Report, which the EPA indexes at Find Your Local CCR, or test the tap with a strip kit.

Other Cities in New York

White Plains ranks 8 of 10 listed New York cities, hardest first. Hardness tracks geology and source more than distance, so neighboring cities can differ widely.

CityHardness (PPM)GPGLevelSource
White Plains 30 ppm 1.8 Soft Surface
Syracuse 130 ppm 7.6 Moderately Hard Surface
Buffalo 120 ppm 7 Slightly Hard Surface
Binghamton 110 ppm 6.4 Slightly Hard Surface
Rochester 95 ppm 5.6 Slightly Hard Surface
Utica 85 ppm 5 Slightly Hard Surface
Poughkeepsie 55 ppm 3.2 Soft Surface
Albany 45 ppm 2.6 Soft Surface
Yonkers 25 ppm 1.5 Soft Surface
New York City 22 ppm 1.3 Soft Surface

Frequently Asked Questions

Does White Plains have hard water?

No. The water is soft. White Plains's water measures 30 ppm (1.8 grains per gallon), which the USGS classifies as soft (0–60 mg/L as calcium carbonate). That is 35 ppm softer than the New York average of 65 ppm and softer than 85% of the 428 cities listed on this site.

What is the water hardness in White Plains in grains per gallon?

1.8 grains per gallon. The same 30 mg/L reading is 1.7 German degrees (°dH), 3 French degrees (°fH) and 0.3 mmol/L; 1 grain per gallon equals 17.1 mg/L as calcium carbonate.

Do I need a water softener in White Plains?

No. At 30 ppm White Plains's water is soft and there is nothing for a softener to remove. Spend the money on a filter if taste is the concern.

What size water softener does a family of four need in White Plains?

None. White Plains's water is soft (30 ppm), so no softener is needed at any household size.

What hardness setting should my dishwasher use in White Plains?

Set it for 1.8 grains per gallon, or 1.7 °dH if the manual uses German degrees; most machines take the nearest step up. The setting controls how much rinse aid and, on models with a built-in softener, how much salt the machine uses.

Where does White Plains's water come from?

White Plains Water Department supplies White Plains from surface water (rivers, lakes and reservoirs). Surface water has little contact with mineral-bearing rock, so its hardness mostly reflects the watershed's geology and tends to run lower and steadier than well water. The utility's annual Consumer Confidence Report lists the current hardness, pH and dissolved solids; the EPA keeps a finder for these reports.

How does White Plains compare with other cities in New York?

White Plains ranks 8 of 10 New York cities listed here, hardest first, and is 35 ppm softer than the New York average of 65 ppm. Nationally it is softer than 85% of the 428 cities listed on this site; the median listed city is 125 ppm.

How This Page Works

  • The hardness, pH, dissolved-solids, source and utility values are the figures reported by White Plains Water Department; every other number on the page is arithmetic on them. The site's five-band scale (soft, slightly hard, moderately hard, hard, very hard) is shown alongside the four-band USGS classification.
  • Unit conversions use 17.1 mg/L per grain per gallon, 17.85 mg/L per °dH, 10 mg/L per °fH and 100.09 mg/L per mmol/L of calcium carbonate.
  • Softener sizing assumes 75 gallons per person per day, regeneration every 7 days, standard capacities from 24,000 to 80,000 grains and 1 lb of salt per 3,000 grains. A dealer will size from your meter and a tap test.
  • Water-heater figures scale the Battelle Institute's 2009 per-5-gpg results linearly to this city's hardness and cap at the 48% loss Battelle measured at 30 gpg; the study ran 90-day accelerated tests, not 15 real years.
  • Sources: USGS Water Science School, Hardness of Water (classification bands); Water Quality Research Foundation, Battelle study release, April 13 2010 and WQA's Softened Water Benefits Studies page; US EPA, Secondary Drinking Water Standards (TDS 500 mg/L, pH 6.5–8.5) and Consumer Confidence Reports.

Test & Treat Your Water

Find out exactly what's in your water and get the right solution.

Some links above are affiliate links — if you buy through them we may earn a small commission at no extra cost to you. As an Amazon Associate we earn from qualifying purchases.